MAP-2100

Rack-mounted test unit for remote BER tests

The one tool data center operators need to remotely test transmission quality of the network connecting its data centers, central offices, or head ends.

MAP-2100

Securing the integrity of data stored in data centers is so important that most data center operators back up data to other data centers via high-performance network links. To maintain the performance of those connections and to verify SLAs, a data center must frequently perform bit-error-rate (BER) tests on Ethernet line rates up to 100G and beyond, as well as OTN, CWDM, or DWDM circuits. The problem is that many data centers have very few, if any, technicians to run tests ensuring the quality of connections.

The MAP 2100 was designed to enable data center operators and network service providers to securely run high-performance bit error rate tests to unmanned locations.


MAP-2100


Key Use Cases

  • Office-to-office (data center interconnect)
    • Scenario: Need to test the network between sites, but neither site has a technician to run tests via portable,
    • hand-held testers
    • Solution: MAP-2100 at both sites, run tests remotely via secure communications
    • Encryption up to 256 bits
    • Additional security by forward all management connectivity through SSH (port ­­)
  • Manual-to-office
    • Scenario: Two sites, but only one with a portable tester and a technician present – typically, this is a two-person
    • Test
    • Solution: Use a portable T-BERD/MTS-5800 on one site and test against a rack-mounted MAP-2100 in the other
    • Only one technician is required to run the test saving expense, man hours
    • Either test unit can be controlled by the other using Smart Access Anywhere
  • Submarine
    • Scenario: Multiple plants with a mix of terrestrial, dry, and wet. Need to test between plants to ensure the network is performing to capacity.
    • Solution: Deploy MAP-2100 units at multiple sites to provide efficient, high-capacity testing with minimal technician intervention.
  • Software-based Test and Measurement (Fusion)
    • Scenario: A “hybrid” network with a mix of physical and virtual circuits has multiple test points; portable, rack-mounted, and virtual, with a need to control them all from a central location via a northbound Netconf/YANG interface
    • Solution: VIAVI Fusion runs standardized BERT and performance monitoring (TWAMP) over multiple test points, both physical and virtual, via an LMAP-compliant architecture.

Highlights:

  • Optimized for remote, un-manned testing with a rack-mounted design and remote management functionality
  • Ethernet testing, 1G through 100G line rates (10G, 25G, 40G, 100G)
  • Complete support of protocols including Ethernet, OTN, SONET/SDH, PDH, Fiber Channel up to 32G, CPRI

Applications:

  • Remotely test the transmission quality of the network links connecting data centers or central offices/head-ends
  • Converged Ethernet/IP network testing and troubleshooting at 10 Mbps to 100G interfaces for data centers and core / metro networks
  • Installation and maintenance of OTN and legacy SONET/SDH and DSx/PDH networks
  • Data service turn-up, performance validation and monitoring for Submarine Cable Networks

Key Features:

  • Rack mounted, 1U 19” wide, kits available for 21”
  • The industry’s fastest RFC 2544 and Y.1564 SAMComplete™ Ethernet service activation test including nanosecond accurate latency measurements. Also supports RFC 6349 TrueSpeed
  • Ensures SFP+/SFP28, QSFP+/QSFP28, and CFP4 modules run error-free with the field optimized Optics Self-Test
  • Test OTN service activation with the OTN Check workflow automated script
  • Test synchronization and timing using built-in GNSS
  • Fiber Channel up to 32G
  • SONET SDH/PDH
  • Ethernet One-Way Delay with built-in GNSS

Part of The VIAVI Remote PHY Solution

This product is part of the comprehensive VIAVI Remote PHY turn-up and maintenance solution enabling seamless transitions from legacy to distributed access architectures.

Приложения к руководствам

Брошюры

Практические кейсы

Постеры

Краткие руководства пользователя

Ceрвисы

Программное обеспечение

Software Downloads

Службы

Instrument Care Support Plans

Save up the 50% of standard service prices and obtain priority service when you buy a bundled plan at the same time the instrument is purchased. Care Support Plans offer the best way to purchase extended warranty, premium technical support, self-paced training, and critical maintenance services like calibration services that include software and engineering change order update services to ensure your product is maintained with current software and a calibration certificate. These discounted plans are 2-5 years long when purchased upfront with your VIAVI instruments.


VIAVI Care Support

VIAVI Care Support

УслугиBronzeCareSilverCareMaxCareGoldCareFleetCare
 BronzeCareSilverCareMaxCareGoldCareFleetCare
Техническая поддержкаПремиумПремиумПремиумПремиумПремиум
Заводской ремонт

Стандартные услуги + специальное меню.
 Калибровка и обучение на местах, выезд инженера технической поддержки,
заказная разработка или подписка на ПО

Приоритетное обслуживание
Онлайн-обучение

Гарантия 5 лет на аккумулятор и сумку*

 
Заводская калибровка 

Гарантия на аксессуары

  
Экспресс-кредиты  

* только для 5-летних программ

Гарантия на замену батареи/сумки
Батареи и сумки изнашиваются от каждодневного использования и в результате циклов зарядки. Чтобы этот фактор не повлиял на результативность работы, в 5-летних программах предусмотрена возможность замены аксессуаров.

VIAVI обеспечивает разовую замену вышедшей из строя батареи и изношенной сумки/перчатки в течение 5-летней программы поддержки SilverCare или MaxCare. Замена проводится только при возврате оборудования в VIAVI на ремонт или калибровку. Программа не охватывает жесткие футляры и не распространяется на оборудование, продаваемое без сумки/батареи.

Действует на 5-летних программах Silver и MaxCare.

Экспресс-кредиты
Now you can schedule calibrations or repairs with no downtime. The Express Loaner Service provides you with a similarly configured piece of equipment before sending yours in for calibration or for that unexpected repair that you need immediately.

Замена аксессуаров MaxCare
Контрольно-измерительное оборудование поставляется с кабелями и разъемами. Для обеспечения достоверности тестирования программа включает в себя замену одного аксессуара один раз в год.

Если аксессуар будет признан дефектным или вышедшим из строя, VIAVI заменит или отремонтирует его (по своему усмотрению) бесплатно для клиента. Замененные аксессуары могут быть новыми или восстановленными. Все возвращенные аксессуары становятся собственностью VIAVI. Действуют следующие ограничения: допускается замена не более чем одного аксессуара в течение 12 месяцев; программа распространяется только на те аксессуары, которые считаются незаменимыми для работы оборудования и поставлялись с изначально приобретенным продуктом. Клиент несет обязательство по отправке вышедшего из строя аксессуара в VIAVI, если его надежность вызвала вопросы во время калибровки или ремонта.


Программы технической поддержки - MAP

Care Support Plan - MAP

Тип продуктаРекомендуемая программаBronzeCareSilverCareMaxCareДля чего нужна калибровка?
  BronzeCareSilverCareMaxCare 
MAP (Mainframe/Module)Bronze-3

Зачем калибровать этот продукт?
Каковы распространенные проблемы?

Factory standards to ensure accuracy MAP

Why calibrate this product?

It is essential in manufacturing environment to ensure your product meets the published/customer requirements. Having accurate measurements ensures highest possible yields whilst maintaining product specifications. Ensuring all that the optical test equipment is performing as designed and calibrated is requirement in achieving that goal.

Viavi will validate measurement accuracies conform to published specifications.

Maintain connectors and pigtails.

Factory standards to ensure accuracy

VIAVI is a TL9000 company and calibrates this instrument based on general requirements for the competence of calibration and testing laboratories (ISO/IEC 17025:2005) to ensure your instrument is certified to measure accurately. Instruments that are out of calibration will produce unreliable measurements and can create false passing or false failing test results that often cause your team repeat work. We maintain, polish and clean all fiber connectors, fix pigtail connections that are internal to the product to ensure all parts stay in good working order and upgrade software / firmware to the latest approved release to enable enhancements. VIAVI Care Plans are the most cost-effective way to plan for calibration with a low, discounted price at the time of instrument purchase.  Fixed rate calibration can also be purchased later via a separate purchase order.

  • Ensure accurate measurements that meet design expectations and optical budgets.
  • Maintain ports and connectors to keep signals working properly and to extend the life of the instrument. For example, if optical connectors or lasers are bad or interface ports are loose then after repeated connection cycles, optical measurements may be inaccurate or damage may occur.
  • When manufacturing optical network products, accurate, reliable and repeatable optical measurement performance is essential to compliance with published/committed product specifications
  • Know that optical product design, product manufacturing and customer expectations are accurate and in alignment throughout product lifecycle

Most business common implications MAP

How will my measurements be affected if the product is out of calibration?

Inaccurate measurements may prevent verification of power levels or introduce other measurement uncertainties, errors and artifacts. Out-of-calibration instruments can result in design errors, production problems, end customer escalations, increased failure rates, audit non-compliance or even ultimately loss of business. 

What are the most common implications of these issues to the business?

  • Uncalibrated tools produce unreliable measurement results that can't be certified to specifications and may violate product agreements or ISO/TL9000 standards with your customers and their network equipment vendors.

  • Design errors resulting from inaccurate measurements can result in ongoing issues throughout the product lifecycle including poor yields, inaccurate optical budgets, increased return rates  and customer expectation mismatch.

  • Production costs can be elevated by increased re-work, reduced yield and inconsistencies between measurements.

Common Business impacts include:

  • Lost revenue, customer complaints and increased costs.
  • Quality audit failures.
  • For end customers, repeat product quality issues with vendors often cause added cost, customer dissatisfaction and loss of business.

 


VIAVI Care Support for Existing Equipment

FleetCare
FleetCare

FleetCare plans can be customized to include any service entitlements on your fleet of existing equipment. Please fill out a Service Contracts form for a quote.

  • Any collection instruments with a single coterminous renewal date
  • Each contract is customized with any number of annual terms required by the customer
  • Onsite Calibration, Training, Field Application Engineer days can be added

View Support Plans For Existing Equipment


Repair and Calibration

Our products live in rugged environments for over 10 years with 1000s of test connect/disconnect cycles.  We will be there to support you to ensure components that require maintenance like connectors, batteries, and software updates to ensure you are ready to test accurately for years to come. We apply factory procedures that use fast, automated calibration and functional verification, maintenance using OEM parts and the application of all engineering change orders and software updates. Services are available through contract Care plans, FleetCare or per incident as requests. 

Top 4 Reasons to Choose VIAVI for Your Repair and Calibration Needs:

  • Minimize business disruption
  • Budget
  • Measurement Accuracy and Product Reliability
  • Measurement Compliance, TL9000 certification and OEM Standards

Explore More


Награды и достижения

Пресс-релизы

С чего начать?

Желаете увидеть демонстрацию нашей продукции? Обращайтесь к нам для получения дополнительной информации, ценовых предложений, а также сведений об оформлении заказа.