CT-4 (Discontinued)

Digital Channel Tagger

The CT-4 is a Digital Channel Tagger that is used as a system with the Seeker D Digital Leakage Detector to detect leaks in the Aeronautical and LTE frequency bands and eliminate all 'false alarm' triggers by providing proprietary dual CW carriers at two locations.

CT-4
This product has been discontinued.

This product has been discontinued

Please consider this product instead:

September 8, 2023
  • Generates Proprietary Dual CW Carriers for use with the Seeker D Digital Leakage Detector
  • Operates in both the Aeronautical (135 to 139 MHz) & LTE (610.5 to 615 MHz) Frequency Bands
  • Adjustable Output from 10 to 30 dBmV
  • Carriers Injected at ~30 dB Below Adjacent Digital Carriers Eliminating the Risk of Affecting Digital Services
  • Unsurpassed Sensitivity from 2 to 2000 uV/m

The new CT-4™ is a 1U rack mounted unit that is located in the head end that provides an uncompromising tagging solution for active analog or digital systems.

When several CATV systems operate in the same area, it is often difficult to determine which system is the source of a detected leak. The CT-4 is designed to deal with the problem of leakage identification in dual cable or overbuilt situations.

Used as a system with the VIAVI leakage receivers, the CT-4 eliminates all “false alarm” triggers and increase leak detection sensitivity by four times over un-tagged systems.

Digital Tagging
The CT-4™ works in conjunction with the new Seeker D™ Digital Leakage Detector to accurately detect and measure signal leakage within the LTE and aeronautical frequency bands.  

The Seeker D detects the proprietary signal from the CT-4 with an unsurpassed sensitivity of 2 to 2000 uV/m with measurements that are scaled to an analog or QAM carrier of your choice. 

Consequently, readings taken from the existing Seeker meter and the new Seeker D meter produce similar results in the aeronautical band if the low band correlation of the Seeker D is set to analog.

Whether testing for leaks in both digital and analog systems, or monitoring aeronautical bands or LTE, the CT-4 used in conjunction with the Seeker D provides all of the capability to find and fix leaks quickly, accurately, and effectively.

Traditional Channel Tagging
The new CT-4 can also act as a traditional CT-2 or CT-3 analog tagger. When used with legacy VIAVI leakage detectors, this feature provides the ability to detect tagged leaks and ignore untagged leaks, saving time from false alarms from signals not originating in your system.

The CT-4™ solves this problem by tagging the system video carrier (CT-2 operation mode) or an integrated carrier  (CT-3 operation mode) with a low-frequency modulation. 

With the tag function switched on, the Searcher Plus GT, Super Plus, Seeker Lite, Seeker Lite², Seeker and Seeker SE leakage detectors are immune to false alarming. 

These leakage detectors all contain special circuitry that is sensitive only to the tagged signal from the CT-4 and rejects any signals that do not contain it.

Warbling Identifier Tone
Searcher Plus, Searcher Plus GT, or Super Plus analog leakage detectors generate an audible tone that varies in pitch with leak strength.  A leak that has been tagged using the CT-2 or CT-3 operation mode of the CT-4 causes the audible tone to “warble,” rising and falling in pitch at the rate of three oscillations per second.  If the distinctive warbling sound is not detected, the operator can be sure that the leak did not originate in his system.

Easy to Install
The CT-4 is very simple to install where RF signals reside. When being used in either the CT-4 or CT-3 operation modes, the CT-4 is simply installed in a rack location near a combiner. Otherwise, the CT-4 can be used with any type modulator in the CT-2 operation mode by simply feeding the analog carrier through the CT-2 and then out to the combiner.

Options

  • 120 to 240 VAC Power Input
  • -48 VDC Power Input

Services

Repair & Calibration

Our products live in rugged environments for over 10 years with 1000s of test connect/disconnect cycles.  We will be there to support you to ensure components that require maintenance like connectors, batteries, and software updates to ensure you are ready to test accurately for years to come. We apply factory procedures that use fast, automated calibration and functional verification, maintenance using OEM parts and the application of all engineering change orders and software updates. Services are available through contract Care plans, FleetCare or per incident as requests. 

Top 4 Reasons to Choose VIAVI for Your Repair and Calibration Needs:

  • Minimize business disruption
  • Budget
  • Measurement Accuracy and Product Reliability
  • Measurement Compliance, TL9000 certification and OEM Standards

Explore More


How to Get Started

Interested in a product demonstration? Contact us for more info, receive a price quote, or find out how to buy.